Remodel electrical wiring in the Twin Cities
Wiring for your kitchen, bath, basement or addition, planned with your contractor and passed by inspection.
- Circuits and device spots are agreed before rough-in starts
- We check your panel can carry the new load before walls close
- We schedule rough-in and final inspections for you
- MN License #EA807704
- Bonded & insured
- Permits & inspections handled
- Free quotes
Get your free quote
Takes 30 seconds. No obligation.
We will call you to talk through the job and set up your free quote. Need us sooner? Call 612-991-4005.
Your email app should open with your request filled in. Press send, or call 612-991-4005.
Electrical Remodels & Renovations, start to finish
- Circuit and device layout plan
- Rough-in wiring while walls are open
- Check of existing wiring
- GFCI and AFCI protection where required
- Devices and fixtures installed after paint
- Permit and inspections
Three steps to a finished job
- Tell us what you need
Call 612-991-4005 or send the short form. Quotes are free.
- Get a written scope and price
We look at the job and put the scope and price in writing before any work starts.
- We do the work and get it inspected
We pull the permit, do the work, and the inspector signs off.
Common questions
Do I need to bring the whole house up to code for a small remodel?
Can you work with my general contractor?
Why is the electrician needed before the drywall goes up?
My house has old wiring. Will it all need to be replaced?
More about electrical remodels & renovations
Remodel electrical is different from new construction. Walls are finished, ceilings are low, and the existing wiring may be decades old and undocumented. Our job is to find out what is behind the surfaces, decide what can stay, and bring the affected areas up to current requirements.
In the Twin Cities that often means working in older houses with plaster walls, knob-and-tube remnants, undersized panels, or a basement that has never had proper circuits. We handle the rough-in before drywall and the finish work after paint, and we coordinate with your general contractor so inspections and trades line up.
Whether you are the homeowner running the project or the builder managing several trades, we will give you a clear scope covering what is being added, what is being replaced, and what the inspector will want to see.
When you need it
- You are gutting or reworking a kitchen and need new countertop, appliance and lighting circuits.
- A bathroom remodel adds a fan, heated floor, vanity lighting or a relocated vanity.
- You are finishing a basement and need receptacles, recessed lighting, smoke and CO detection, and possibly egress or sump circuits.
- An addition, sunroom or second-story build needs new circuits and probably more panel capacity.
- You are opening walls in an older home and find ungrounded, cloth-covered or spliced wiring.
- You want to rearrange rooms, move a doorway or add built-ins that disrupt existing switches and outlets.
- Your builder needs a licensed electrician for rough-in, inspection and finish on a defined schedule.
What’s included, in detail
Circuit counts, device locations and lighting layout are agreed before rough-in starts.
New cable runs, boxes and circuits installed while the framing is open.
We check what is in the walls and flag anything that should be replaced rather than reused.
We confirm the panel and service can carry the new loads before the walls are closed.
GFCI, AFCI and tamper-resistant devices installed where the rules for that room require them.
Devices, cover plates, fixtures and fan hookups installed after drywall and paint.
We pull the permit and schedule rough-in and final inspections with the right inspector.
Our process
- Walk the project
We review plans or walk the space with you and your contractor to understand scope and sequence.
- Rough-in
We run wiring and set boxes ahead of insulation and drywall, then call for the rough-in inspection.
- Close-up and finish
Once walls are finished, we install devices, fixtures and trim.
- Final inspection
We test every circuit, pass the final inspection and walk you through what was changed.
More questions
Can you help choose lighting and fixture placement?
Guides
Often done together
Ready for your free remodel wiring quote?
Call or send the short form. You get a written scope and price before any work starts.