Electrical troubleshooting and repair in the Twin Cities
We find the cause of tripping breakers, dead outlets and flickering lights, then fix it.
- We test to find the actual fault, not guess
- We tell you what we found and what we did
- We repair earlier work that is not up to code
- MN License #EA807704
- Bonded & insured
- Permits & inspections handled
- Free quotes
Get your free quote
Takes 30 seconds. No obligation.
We will call you to talk through the job and set up your free quote. Need us sooner? Call 612-991-4005.
Your email app should open with your request filled in. Press send, or call 612-991-4005.
Troubleshooting & Repairs, start to finish
- Fault diagnosis
- Switch, outlet and fixture replacement
- Wiring repair with proper junction boxes
- Breaker and panel checks
- Fixes for overloaded circuits
- Clear explanation of the work
Three steps to a finished job
- Tell us what you need
Call 612-991-4005 or send the short form. Quotes are free.
- Get a written scope and price
We look at the job and put the scope and price in writing before any work starts.
- We do the work and get it inspected
We pull the permit, do the work, and the inspector signs off.
Common questions
Why does my breaker keep tripping?
An outlet has stopped working. Is it dangerous?
Can you repair things that were wired by someone else?
Do repairs need a permit?
More about troubleshooting & repairs
Electrical troubleshooting is the process of tracing a symptom, such as a breaker that keeps tripping, an outlet that has no power or lights that flicker, back to its source. The cause might be a worn device, a loose connection, a damaged cable, an overloaded circuit or a problem at the panel or service. Replacing parts without finding the cause often means the problem comes back.
We start by understanding what you are seeing and when it happens, then test the circuits to isolate the fault. Once we know the cause, we explain it plainly and recommend a repair, whether that is replacing a device or correcting wiring. Repairs that require a permit get one, and the work is inspected by the Minnesota Department of Labor and Industry or the local jurisdiction.
Minnesota adds its own stresses to electrical systems, including cold garages and exterior outlets, moisture in basements, and aging wiring in older Minneapolis and St. Paul housing. Prime Time Electric MN, LLC is a licensed contractor (License #EA807704) serving homes and businesses throughout the Twin Cities.
When you need it
- A breaker trips repeatedly or will not stay reset
- Outlets or switches have stopped working, or only work some of the time
- Lights flicker, dim when appliances start, or buzz
- You notice a burning smell, warm or discolored outlets or switch plates, or crackling sounds, and have turned off the affected circuit
- A GFCI or AFCI device keeps tripping without an obvious cause
- Part of a building has lost power while the rest still works
- An addition, renovation or earlier electrical work left something not working as it should
What’s included, in detail
We test circuits, devices and connections to isolate where the fault actually is.
Failed switches, receptacles, dimmers and fixtures are replaced with suitable devices.
Damaged, loose or incorrectly spliced wiring is repaired or replaced, with proper junction boxes.
We investigate breakers that trip or fail and panel components that show heat damage or wear.
If a circuit is overloaded or shares loads it should not, we recommend and carry out a fix.
We repair problems from earlier work that does not meet code or is not working as intended.
We tell you what was found, what was done, and anything else we noticed that deserves attention.
Who it’s for
For homeowners
A dead outlet or a breaker that keeps tripping can be a minor device failure or a sign of something more serious, and it is hard to tell which without testing. We find the cause, explain it in plain terms, and show you the options before work begins. If we see other issues while we are there, such as a loose panel connection or an ungrounded outlet, we will mention them so you can decide what to do. Please do not open panels or work on wiring yourself, because that is a job for a licensed electrician.
For property managers
Repeat electrical complaints from tenants cost time, and swapping devices without finding the cause tends to bring the same call back. We trace the fault to its source, repair it properly, and tell you plainly what was done so you can keep your maintenance records straight. If a unit shows signs of a larger issue, like overloaded circuits or aging panels, we will say so and discuss options. We work with owners and managers of Twin Cities properties and aim for clear, responsive communication.
For businesses
In a commercial space, an electrical fault can interrupt operations, so we aim to diagnose it carefully and repair it correctly the first time. We work on lighting, receptacles, equipment circuits, panels and the problems that come with tenant changes or added equipment. We can plan the work around your hours where possible and keep you informed of what is being done and why. Repairs are made to code, permitted when required and inspected by the state or the local jurisdiction.
Our process
- Describe the problem
You tell us what is happening and when, and we ask the questions that help narrow down the cause.
- Test and isolate
We test the circuit and its devices to find the fault, and check connected areas for related issues.
- Explain and agree on repair
We explain what we found and the options, and you decide how to proceed before we do the work.
- Repair and verify
We make the repair, pull a permit where one is required, and test to confirm the problem is resolved.
More questions
How much does a repair cost?
Guides
Often done together
Ready for your free repair quote?
Call or send the short form. You get a written scope and price before any work starts.