MN Licensed Electrical Contractor #EA807704|Serving the Twin Cities metro
sales@ptelectricmn.com612-991-4005
612-991-4005Free Quote
Home
Residential
Commercial
Property Management
Safety & Code
About Guides Service Area Contact
CallFree Quote

Recessed lighting installation in the Twin Cities

Clean recessed lights in new or finished ceilings, spaced well and dimmable.

  • We mark the layout to avoid joists, ducts and plumbing
  • We use remodel fixtures so finished ceilings stay intact
  • Dimmers are matched to your LED lights
Get a free recessed light quote612-991-4005
  • MN License #EA807704
  • Bonded & insured
  • Permits & inspections handled
  • Free quotes

Get your free quote

Takes 30 seconds. No obligation.

Licensed, bonded & insured · MN #EA807704

Prefer to talk? Call 612-991-4005

What you get

Recessed Lighting, start to finish

  • Ceiling layout and spacing
  • New-work or remodel housings
  • Insulation-rated fixtures
  • New cable runs and switch wiring
  • Dimmer and matching color temperature
  • Trim seated tight to the ceiling
Electrician installing pendant light fixtures over a kitchen counter
Installing pendant fixtures over a kitchen counter.
How it works

Three steps to a finished job

  1. Tell us what you need

    Call 612-991-4005 or send the short form. Quotes are free.

  2. Get a written scope and price

    We look at the job and put the scope and price in writing before any work starts.

  3. We do the work and get it inspected

    We pull the permit, do the work, and the inspector signs off.

Get a free quoteCall 612-991-4005
FAQ

Common questions

Can recessed lights go into a finished ceiling?
Yes, with remodel-style housings or slim LED fixtures that mount through a cutout. Access above the ceiling affects how easy the wire run is, and we may need to open small sections of drywall in some cases.
How many recessed lights do I need?
It depends on ceiling height, room size, the brightness of the fixtures and what the room is used for. Rather than a fixed rule, we lay out a pattern and adjust it to the room's furniture and tasks.
Will recessed lighting cause heat or energy loss in my attic?
Not if the right fixtures are used. Insulation-rated, airtight fixtures limit heat buildup and air leakage, which matters in a cold climate, and we choose accordingly.
Can I put them on a dimmer?
Yes. The dimmer has to be compatible with the LED fixtures, which is why we select them together. Mismatched parts are the usual cause of flicker.
More about recessed lighting

Recessed lighting sits flush in the ceiling, so the fixtures themselves disappear and the light stays in the room. Modern LED downlights are shallow, efficient and available in a range of color temperatures, which makes them workable in places where older, deep cans were not.

The ceiling is where the real decisions are. In a Minnesota house, the space above is usually insulated against cold winters, so fixtures must be rated for contact with insulation, and the ceiling must be sealed so that holes do not become air leaks. We choose fixtures with the right rating for the ceiling type and for rooms with moisture, such as showers.

Layout matters as much as hardware. Spacing, distance from walls and the number of fixtures affect whether a room looks evenly lit or spotted with bright circles. We lay it out on the ceiling before cutting anything, then put the whole group on dimmers if you want them. For pendants, porch lights and landscape fixtures, see interior and exterior lighting.

When you need it

  • A kitchen or hallway relies on one center fixture and still feels dark at the edges.
  • You want lighting that does not compete with a low ceiling or a decorative feature.
  • A basement renovation needs lighting that fits under ducts and joists.
  • You are replacing old, deep recessed cans that leak air, run hot or take bulbs that are no longer made.
  • You want to wash a wall or highlight artwork, shelving or a fireplace.
  • Bathroom or shower areas need a fixture rated for damp or wet locations.
  • You are adding a room or finishing a ceiling and want to plan lighting before it is closed.

What’s included, in detail

Ceiling layout

Fixture spacing and placement marked out to avoid joists, ducts and plumbing.

New-work and remodel cans

Housings for open framing, or remodel-style fixtures that install through a hole in finished drywall.

Insulation-rated fixtures

Fixtures rated for insulation contact, and for damp or wet areas where needed.

Wiring and circuiting

New cable runs and switch legs, with the load kept within what the circuit supports.

Dimming and color

Dimmers matched to LED drivers, and consistent color temperature across the room.

Patching and finish

Clean cutouts, trim rings seated tight to the ceiling, and drywall patching coordinated if needed.

Our process

  1. Check the ceiling

    We look at framing direction, insulation, attic access and what is in the way.

  2. Mark the layout

    We mark fixture positions with you so you can see the pattern before any holes are cut.

  3. Cut and wire

    Openings are cut, cable is pulled and fixtures are connected to the switching.

  4. Trim and test

    Trims are installed, dimming is tested and any fixture that is off is corrected.

More questions

Do recessed lights work in a bathroom?
Yes, as long as the fixture is rated for the location. Fixtures directly over a shower or tub need a wet or damp rating, and we match the rating to where each one goes.
Related

Often done together

Interior or exterior lightingLighting installationRemodel or renovation wiring

Ready for your free recessed light quote?

Call or send the short form. You get a written scope and price before any work starts.

Get a free quote612-991-4005
Call nowFree quote